{"product_id":"lowrance-yamaha-engine-interface-cable","title":"Lowrance Yamaha engine interface cable — wired NMEA engine data connection, part 000-0120-37 for RPM, trim, fuel","description":"\u003cp\u003e\u003cstrong\u003eThe Lowrance Yamaha Engine Interface Cable connects compatible Yamaha outboard engines to Lowrance displays to share engine data and diagnostics in real time.\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cp\u003eDesigned for anglers and boaters who rely on accurate engine information, the Lowrance Yamaha Engine Interface Cable (part number 000-0120-37) provides a straightforward wired connection between Yamaha engine electronics and Lowrance multifunction displays. The cable enables the display of RPM, trim, fuel levels and other engine parameters directly on your chartplotter or fishfinder, simplifying monitoring and troubleshooting without adding bulky adapters.\u003c\/p\u003e\n\n\u003ch3\u003eHow does this cable integrate with my Lowrance chartplotter?\u003c\/h3\u003e\n\u003cp\u003eThe cable plugs into compatible Lowrance units and interfaces with Yamaha engine networks to relay NMEA-compatible engine data. Installation typically requires routing the cable from the engine area to the electronics helm and securing connections at both ends.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eDirect physical connection to Lowrance displays supporting Yamaha engine data\u003c\/li\u003e\n  \u003cli\u003eUses manufacturer-specified connectors for reliable signal transfer\u003c\/li\u003e\n  \u003cli\u003eWorks with compatible Yamaha engines and ECUs that output data\u003c\/li\u003e\n  \u003cli\u003eMinimal configuration on the display—select engine data source in settings\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat engine information can I expect to see on my screen?\u003c\/h3\u003e\n\u003cp\u003eOnce installed and paired, the interface cable passes key performance and diagnostic values from the Yamaha engine to your Lowrance unit. The exact parameters depend on the engine model and ECU capabilities, but common readouts are readily accessible.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eReal-time RPM and tachometer readings for engine monitoring\u003c\/li\u003e\n  \u003cli\u003eTrim and tilt position to assist with boat handling and performance\u003c\/li\u003e\n  \u003cli\u003eFuel level and flow where supported by the engine electronics\u003c\/li\u003e\n  \u003cli\u003eBasic diagnostic codes transmitted for quick fault awareness\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eIs installation difficult and what should I watch for?\u003c\/h3\u003e\n\u003cp\u003eInstallation is typically straightforward for users comfortable with basic marine wiring, but follow safe wiring practices and the manuals for both Lowrance and Yamaha. Proper routing and secure connections prevent corrosion and signal issues over time.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eRoute cable away from moving parts and high-heat areas\u003c\/li\u003e\n  \u003cli\u003eUse grommets where the cable passes through bulkheads to prevent chafing\u003c\/li\u003e\n  \u003cli\u003eVerify pin alignment and connector seating before powering up\u003c\/li\u003e\n  \u003cli\u003eSeal exposed connections with marine-grade dielectric grease or heat shrink\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWill this cable fit my Yamaha engine model?\u003c\/h3\u003e\n\u003cp\u003eThe Lowrance Yamaha Engine Interface Cable is compatible with many Yamaha outboards that provide engine data outputs; confirm compatibility by checking Yamaha engine electronics specifications and Lowrance display compatibility lists. If in doubt, consult dealer support or the product manuals.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eCheck Yamaha ECU model and data output type against Lowrance requirements\u003c\/li\u003e\n  \u003cli\u003eRefer to Lowrance device firmware notes for supported engine protocols\u003c\/li\u003e\n  \u003cli\u003ePart number 000-0120-37 identifies this specific interface cable model\u003c\/li\u003e\n  \u003cli\u003eIf needed, contact Lowrance or Yamaha technical support for confirmation\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eWho this is for: This interface cable is intended for recreational boaters, anglers, and marine technicians who want to centralize engine information on a Lowrance display. It's suited to anyone upgrading instrumentation, troubleshooting engine performance, or seeking a cleaner helm with integrated engine readouts—provided their Yamaha outboard and Lowrance unit are confirmed compatible.\u003c\/p\u003e\n\u003csection class=\"product-faq-snippet\"\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Does this cable support engine diagnostics?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Yes, it transmits common engine parameters and basic diagnostic codes from compatible Yamaha ECUs to supported Lowrance displays.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Can I install it myself?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Many users can install it with basic wiring skills, but follow manuals and consider professional help for complex installations.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/section\u003e","brand":"Lowrance","offers":[{"title":"Default Title","offer_id":48030694211745,"sku":"B0012R2PHG","price":257.97,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0758\/6532\/5729\/files\/lowrance-yamaha-cable-front-connector.jpg?v=1791410235","url":"https:\/\/canadiansporting.ca\/products\/lowrance-yamaha-engine-interface-cable","provider":"Canadian Sporting","version":"1.0","type":"link"}