Heurofosh Outboard Engine Support Kit for 2/3-Ram Trim‑and‑Tilt — Reinforced Wedge + Steering Lock Clips (Rubber, Tool‑Free)

Heurofosh Outboard Engine Support Kit is a trailer-ready wedge and steering lock clip set designed to stabilize 2/3-ram trim-and-tilt outboards during road transport.

When trailering a boat with a 2/3-ram trim and tilt system, movement of the motor can stress the transom, steering components, and lower unit. This Heurofosh kit pairs a reinforced rubber wedge-style transom saver with two hydraulic steering lock clips to reduce bounce and limit steering cylinder rotation while towing. The set is an aftermarket accessory made for rapid installation without tools and fits many common outboards when their ram structure and cylinder clearance match the listed dimensions.

How does the wedge support protect my motor and transom during towing?

The wedge support fits over the trim/tilt ram to create a stable point of contact that reduces motor shift and shock load on the transom. By supporting the motor at the ram location, it helps minimize movement that can tug on steering cables, hydraulic lines, and the lower unit. It’s shaped and sized to distribute pressure rather than concentrate it, and its reinforced materials are suited for repeated trailering use.

• Wedge length approx. 8-3/4 inches for adequate ram coverage
• Rubber and reinforced plastic construction for durability
• Installs quickly without tools; sits over 2/3-ram trim/tilt rods
• Reduces motor bounce and transom stress during transport

Will these steering lock clips fit my outboard’s hydraulic cylinders?

The kit includes two steering lock clips about 4 inches long, intended to limit steering cylinder rotation and hold the wheel alignment while trailering. Fit depends on the steering cylinder shape and available clearance around the ram and steering linkage, so verify dimensions before ordering. The clips are made for hydraulic steering setups commonly found on larger outboards.

• Approximately 4 inches long steering stop clips included
• Designed for hydraulic steering cylinders on 2/3-ram systems
• Check cylinder clearance and ram structure compatibility first
• Quick snap-on installation; no special tools required

Which engines and models are compatible with this Heurofosh kit?

The kit is formulated for a range of mainstream outboards that use 2/3-ram trim and tilt systems. It lists compatibility with common horsepower ranges, but it is not an OEM component, so physical verification of ram position and steering geometry is recommended. The kit covers many Yamaha, Mercury, Honda, Johnson/Evinrude, Tohatsu, and Suzuki outboards within the specified HP ranges.

• Yamaha: 115–350 HP models with matching 2/3-ram systems
• Mercury: 135–300 HP with compatible ram geometry
• Honda: 90–300 HP outboards with 2/3-ram fit
• Johnson/Evinrude: 150–300 HP (excluding Generation 2)
• Tohatsu: 115–250 HP and Suzuki: DF140–DF300 where ram matches

How easy is it to install and carry on the boat or trailer?

Installation is tool-free and intended for quick use at launch sites or when preparing for transport. The wedge slips over the trim/tilt ram and the clips snap onto steering cylinders; both components are compact for storage on the boat or trailer. Because the kit is aftermarket and made of rubber and reinforced plastic, it’s lightweight enough to stow in a tackle locker or storage compartment.

• Tool-free installation for both wedge and clips
• Compact wedge and two clips for easy storage on board
• Durable materials intended for repeated trailering cycles
• Not an OEM part — verify fit for your setup before use

Who is this for: The Heurofosh Outboard Engine Support Kit suits boat owners and trailering professionals who use 2/3-ram trim-and-tilt outboards and want a practical aftermarket solution to limit motor movement while towing. It’s intended for owners of compatible Yamaha, Mercury, Honda, Johnson/Evinrude, Tohatsu, and Suzuki engines who can confirm ram structure and steering cylinder clearance prior to purchase. If you need a lightweight, tool-free support to reduce transom stress and stabilize steering gear on the road, this kit is designed for that use.