XIKOBY Razor E100 E125 E175 Replacement Controller Kit — 4‑Wire Throttle Module + Rubber Grips (V10+/V18+)

XIKOBY's replacement control module and rubber handlebar grips update Razor E100-series scooters to restore responsive throttle and a secure hold.

If your Razor E100, E125 or E175 scooter no longer accelerates or the throttle feels loose, this kit from XIKOBY supplies a direct-fit controller and new grips designed for specific later-version models. It replaces legacy part numbers ZK2400-DP-LD, ZK2400-DP-FS and W13111612015 and includes the 4-wire throttle connector standard on later E100-series electronics. Read the compatibility notes carefully—this unit fits later revisions only and is not for Power Core, Black Label, Glow models, or earlier Version 1–10 systems.

Will this controller work with my Razor scooter model and version?

The XIKOBY controller is engineered to match Razor E100 and E125 scooters from Version 10 onward and E175 from Version 18 onward, plus compatibility with E150 Tri-kke E2 and Espark across versions. It is not compatible with older revision boards or the Power Core / Black Label / Glow variants. Check your current controller part number and wiring before purchasing to ensure a correct swap.

• Fits: Razor E100 (V10+), E125 (V10+), E175 (V18+), E150 Tri-kke E2, Espark
• Replaces parts: W13111612015, ZK2400-DP-LD, ZK2400-DP-FS
• Not for: Razor Power Core E100, Black Label E100, E100 Glow, or V1–V10 boards
• Includes 4-wire throttle connector required for later models

How do I install the XIKOBY control module and grips?

Installation is straightforward for someone comfortable with basic scooter wiring and hand tools, but always disconnect the battery first. Because E100-series scooters require a push-start and throttle twist to engage the motor, verify the wiring harness matches the 4-pin connector on the replacement module before finalizing the mount.

• Disconnect battery and remove handlebar cover to access controller
• Confirm matching 4-wire throttle connector and plug securely
• Mount controller where original unit sat and secure all screws
• Slide on new rubber grips and test acceleration outdoors at low speed

What improvements will I notice after swapping to this controller?

Once installed, the control module can restore throttle responsiveness and consistent motor engagement on supported scooters, while the fresh rubber grips improve hand control and comfort on rides. The unit provides the same connector layout as the later-stock boards, so performance should match factory behavior when installed correctly.

• Sharper throttle response and reliable motor engagement
• Durable rubber grips for firmer, longer-lasting hold
• Plug-and-play wiring for later-version E100-series scooters
• Replaces worn or faulty controller components to extend scooter life

Are there installation cautions or wiring differences to watch for?

Yes—this replacement matches later-version electronic layouts and uses a 4-wire throttle connection; older scooters may have different pinouts. Double-check that the scooter requires a push start (typical for E100 family) and that you understand which wires correspond to battery, motor, brake, and throttle before powering up.

• Verify Version (V10+ for E100/E125, V18+ for E175) before purchase
• Confirm 4-pin throttle connector and overall harness compatibility
• Avoid forcing mismatched plugs—consult wiring diagrams if unsure
• Test function in a safe, open area after installation

Who is this for: This XIKOBY controller and handlebar grip kit suits owners of compatible Razor E-series scooters who need to replace a failing controller or refresh worn grips. It's aimed at DIYers and repair technicians comfortable with basic electrical connections and looking to restore throttle performance and rider comfort on later-version E100, E125, E175, E150 Tri-kke, or Espark models. If your scooter is an earlier revision or one of the excluded special editions, choose a compatible replacement designed for those versions instead.